Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

$24.95
To prevent poor shifting and uneven drivetrain wear, most manufacturers recommend chain replacement at or before 1% stretch. Now you can quickly and accurately determine the wear and stretch of any chain with Park's Chain Checker. Simply insert the Chain Checker’s pins into 2 links, press the swingarm gauge tight, and then check the gauge window for an accurate reading!
$10.95
Park's Hex Wrench Set offers all the popular Allen wrenches (1.5, 2, 2.5, 3, 4, 5 and 6mm) in a convenient fold-up unit. The tool tips are chamfered for a positive grip and the one-piece fiber-reinforced-resin handle is light, comfortable, slip resistant and 40% stronger than steel.
$30.95
Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts. - Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes - Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain - Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess - Sturdy handle makes the Cyclone easy to use and control - Holds 2 fluid ounces (59ml) of solvent
$41.95
A professional quality shop chain tool that works on 5-speed to 12-speed Road and Mountain Bike derailleur chains*, including SRAM AXS 12 speed, as well as 1/8-inch and 3/16-inch chains. The CT-3.3 features an adjustable locating shelf so it works on any width chain to remove and install chain rivets. Built to last and easy to use, the CT-3.3 features a comfortable handle, investment cast steel body and replaceable driving pin (#CTP). *The CT-3.3 will install, but not peen, Campagnolo 11 and 12-speed chain rivets. - Comfortable T-handle - Replaceable driving pin (CTP) - Investment cast steel body - Adjustable locating shelf
$43.95
Park’s Professional Cable And Housing Cutter is specifically for use on derailleur and brake cables and housing. It even makes quick work of hard-to-cut shift-cable housing. Its cold-forged, heat-treated-steel handles won't bend and its precision-ground jaws cut perfectly every time. Its dual-density molded grips are specially contoured for superior comfort and control. Plus, there’s a built-in cable-end crimper and a forming hole for reforming housing ends.
$28.95
Park's Mini Chain Brute Chain Tool goes anywhere and features a V-shaped handle, a super-strong replaceable pin, and fine threads to make chain removal and installation a breeze. The CT-5 works on any derailleur chain, including Shimano Hyperglide and 9-, 10-, and 11-speed. It works for loosening tight links, too.
$19.95
A favorite of shop mechanics for over 30 year's, Park's CCP-22 Crank Puller removes crankarms that feature square tapers, and those that fit on Power Drive and Power Spline bottom bracket interfaces. The long, comfortable, built-in handle and fine thread provide the leverage needed to remove even the tightest crankarms. And, there's a rotating tip to ensure smooth operation and long life.
$5.95
• Updated to be stronger, smoother, and more versatile • Features a new material and redesigned tip for easier entry into just about any tire, including tubeless • The unique design lifts the tire away from the rim and features a spoke hook to use when multiple levers are needed • This set includes 3 tire levers
$24.95
Park's BBT-18 is a heavy duty, investment cast tool for installing and removing all Shimano, ISIS Drive, and ISIS Overdrive 8-notch bottom bracket cups.
$5.95
Park's Gear Clean Brush has a handle on one end with a curved, serrated edge perfect for cleaning between cassette cogs. The other end's tough nylon bristles are ideal for cleaning the derailleurs, chain and other drivetrain parts to keep them clean and prevent premature wear. It also works great on brakes and other components that collect dirt and grime. The GearClean easily fits in a toolbox or pack.
$42.95
An economical option for safely and accurately tightening fasteners to proper torque specifications. With a simple gauge readout, the TW-1.2 is intuitive and easy to use, and applies up to 14 Nm of torque to any fastener or component with left or right-handed threads. Perfect for low-torque applications such as stem bolts, levers, and carbon fiber components. 3/8" drive for compatibility with all Park Tool sockets, bits, and crow feet. - 0 to 14 Newton meter (0 to 140 inch-pound) range - 3/8" drive - Reads and registers torque values for both left hand and right hand threading - Length: 11.5" (292 mm)
$32.95
Park's Heavy-Duty Tire Levers handle the toughest tire-and-rim combinations including difficult downhill and freestyle tires. Their specially designed tips engage the tire bead so it can be removed with just two levers. Plus, these beefy, forged-steel levers are a full 8-inches long for superior leverage.
$29.95
A great way to hold small parts, tools and components during a repair, Park Tool's Benchtop Overhaul Mat features multiple small pockets and one large work area. It's perfect for suspension work or to organize parts for installation. • Made of a rubber-like PVC • Cleans easily and looks great on any bench • Measures: 14.7” x 7” (38cm x 18cm)
$11.95
Park's Valve Core Tool is great for tightening, removing and installing Schrader and Presta valve cores (the cores are inside the valve), and also Presta valve extenders that have 5mm wrench flats. It's a handy tool to save a tube when all that's wrong is a broken valve, and it also lets you remove valves to easily insert sealant.
$33.95
Park's I-Beam Mini Fold-Up Hex Wrench/Screwdriver/Torx Set with Chain Tool includes 1.5, 2, 2.5, 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen, a regular screwdriver, a T25 Torx tool (for disc-rotor bolts), a tire lever, spoke wrenches and a chain tool. The I-Beam conveniently fits in pockets and packs, too.
$124.95
The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.
$35.95
The CRS-15EXT includes a tube and fitting to extend any CRS-15 to work on fork steering tubes up to 425mm.
$469.95
The DT-5.2 is engineered and built to accurately face front or rear disc brake mounts so they are precisely aligned to the rotor. - Faces any IS Mount, Post Mount, or new Shimano Flat Mount, including low clearance, chainstay mounts - Telescoping axle adaptors allow use with any configuration of open or thru-axle dropouts and dropout widths (including Boost 110, Boost 148 and all fat bike axles) - Includes two facing cutters: IS Mounts Post and Flat Mounts - Includes storage case
$248.98
The 2197 is an add-on accessory for the Park Tool DT-5 and DT-5.2 Disc Brake Mount Facing Set to enable easier and more efficient facing of disc brake mounts on carbon fiber frames. Features a brazed-on diamond grit surface that is over 100 times more durable and effective on carbon fiber than the cutter included with the DT-5.2. The 2197 sits between the cutter of the DT-5.2 and the brake mount, and smoothly and evenly grinds the mounting surface until it is flat and properly perpendicular to the rotor. NOTE: The 2197 is intended for facing carbon fiber only. Aluminum, steel, and titanium disc brake mounts should be faced using the #2171 facing cutter included with the DT-5.2. For carbon frames that feature aluminum inserts (with a carbon/aluminum hybrid mounting surface), use the #2197. When machining carbon fiber, regularly apply water (or a similar solution) to the cutting surface.
$27.95
A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 16-notch tool fittings, including Enduro T47 & PF30 bottom brackets. Manufactured in-house by Park Tool, anodized for easy identification and featuring a ratchet/torque wrench-compatible 3/8" drive. Fits 16-notch bottom bracket tool fittings with a major diameter of 52-54 mm and a minor diameter of 48.8 mm, including: - CeramicSpeed T47/86 - Enduro T47 (30mm and DUB spindles) - Enduro BB30/30a TorqTite (30mm and DUB spindles) - Kogel T47 - SRAM T47 DUB - White Industries T47 - White Industries PF30 Thread-Together
$6.99
Get those heads sealing like new and reduce compressor energy waste with Park Tool's Head Seal Kit. This kit will help get rid of that hissing sound you've been hearing when it has been too long since servicing your Park Tool INF-1 or INF-2 shop inflator. Kit includes: - 1 #1586 Presta Seal - 1 #1588 Schrader Seal - 2 #1576-2 O-rings for Shuttle-valve - 1 #1682-2 O-ring for INF-1 and INF-2 Head Adaptors
$31.95
A great way to keep the benchtop organized during a repair, the OM-2 features an over-sized textured work area and raised trays for organizing small parts and hardware. Perfect for overhauling or rebuilding components such as forks, shocks, hubs, suspension linkages, derailleurs, etc. - Measures 15 x 24.5-inches (38cm x 62cm) - Interlocking edges allow multiple mats to be joined together - Tear/abrasion/shock-resistant TPR construction
$209.88 - $271.32
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.
$5.95 - $7.95
Park's Shop Screwdrivers are pro-quality tools featuring durable and precise heat-treated chrome-vanadium tips and shafts and dual-density handles for an excellent grip.
$26.95
Shop quality L-shaped, high torque industrial steel Torx compatible wrenches. Featuring chamfered tips, tight tolerances and a handy portable tool holder for easy access. Includes: T9, T10, T15, T20, T25, T27, T30 and T40.
$15.95
Park's AWS-7 features a Y-shaped nylon handle with 4 and 5mm Allen wrenches and a T25 Torx wrench. This convenient 3-in-1 tool keeps commonly used wrenches together and offers an excellent grip as well.
$53.98
Accurately gauge the straightness of disc brake rotors while the wheel is mounted in a TS-2.2 or TS-2 Professional Wheel Truing Stand (each sold separately). Park Tool's Rotor Truing Gauge features an infinitely adjustable, finely threaded indicator gauge. It works with any diameter brake rotor.
$52.95
Park's Threadless Star Nut Setter makes it quick and easy to install star-fangled nuts used with 1-inch and 1-1/8-inch threadless headset systems. Using a durable steel driver and built-in guide, the TNS-4 perfectly aligns the star-fangled nut and sets it to the proper depth every time. Plus, the unique design virtually eliminates pinched fingers!
$56.98
Park Tool's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press which is sold separately) BB86, BB90, BB92 and Press Fit bottom brackets from Shimano, Race Face, SRAM and others that use a nominal 24mm-diameter spindle. This tool has a bearing remover that fits inside the bottom bracket shell and into the bearing so the bearings can be tapped out of the frame with a hammer. The set also includes two bushings that you use in conjunction with a bearing press for precision bearing installation (bearing press sold separately).
$19.95
Made for the rigors of everyday shop use, this adjustable tap handle fits many common bicycle taps. • Fits most metric taps from M1.6-M8 • Fits most standard taps from #0-5/16”
Page 1 of 9 Next page